Sep – Oct wax bought and cleanedNov – Jan tapers on the rack1–2 Nov Vėlinės2 Feb Grabnyčios

Beeswax Candle ShedDipped and rolled beeswax candles from a garden shed in Šiauliai

Dipping · shed note

Dipping rhythm and wick sizes: how a pair of tapers is built

A dipped taper is nothing more than a wick lowered into warm wax thirty or forty times and allowed to cool in between. The skill is in the waiting, and in choosing a wick that suits beeswax rather than the paraffin most wick charts were written for.

burns about 7 minutes

Written 22 March 2025Re-dipped 13 December 2025

One dip
three seconds, counted aloud
Between dips
one to five minutes
Dips per pair
thirty to forty-five
Everyday wick
2/0 square braid

Why beeswax wants a bigger wick

Beeswax is denser than paraffin and melts at a higher temperature, so it needs more heat from the flame to keep a small pool of liquid wax feeding the wick. A wick sized for a paraffin candle of the same width drowns in beeswax: the flame shrinks, the pool never reaches the sides, and the candle hollows out down its middle until it goes out. Nearly every problem I had in the first winter came from wicks that were a size or two too small.

I use cotton square braid for all my tapers. It stands straight, curls very slightly as it burns so that the tip is consumed in the flame, and comes in sizes marked with a number and a slash, where 4/0 is thinner than 2/0 and 2/0 is thinner than 1/0. Flat braid is made for paraffin and I no longer keep any. Wick comes on cardboard spools, and I write the size in marker on the spool itself as well as on the packet, because packets get lost.

The numbers I settled on

My numbers come from test burns at the kitchen table, not from a chart, and they belong to my wax, my shed and my candlesticks. A thin taper about fifteen millimetres across at the base burns cleanly on 4/0. The standard pair I make most, around twenty-two millimetres at the base so it fits an ordinary candlestick, burns best on 2/0. The thick Candlemas tapers, which I build out to twenty-five millimetres or more, need 1/0 or they hollow out.

The test is simple and slow. I light one candle from each pair in a room without draughts, standing on a plate, and watch it for an hour with a ruler and the notebook. A well-wicked taper burns with a steady flame two or three centimetres tall, a small clean pool, no smoke and no drips down the side. If it drips, the wick is too big for the width. If the flame shrinks and the wax walls rise around it, the wick is too small.

On the card by the pot

  • Thin taper, about 15 mm at the base: 4/0 square braid
  • Everyday pair, about 22 mm at the base: 2/0 square braid
  • Candlemas taper, 25 mm and over: 1/0 square braid
  • Trim the wick to about 6 mm before every lighting
  • Change one thing per test pair, never two

Priming and hanging the wick

A length of wick is cut to twice the height of the candle plus a hand's width, so it can hang over a rod with a candle forming on each end. Before the real dipping starts I prime it: one long dip of about thirty seconds, so the wax soaks right into the cotton and pushes the air out, then a pull between finger and thumb to straighten it while it cools. Air left in the braid comes out later as a spitting, jumpy flame.

To stop the two candles sticking together, I fix a small spacer on the wick at the fold, a short piece of dowel with two notches cut in it, so the pair hangs a finger apart. A steel nut tied to the bottom of each end keeps the primed wick straight through the first few dips, and I cut it off once the candle has enough weight of its own. The nut must be steel, never brass, for the same reason the can must never be copper.

The rhythm of forty dips

Each dip is one smooth movement: down into the wax, a moment's pause, and up again, three seconds in all, counted aloud until it becomes habit. Too slow and the hot wax melts off the layer laid down before. Too quick and the new layer goes on thin and patchy. Between dips the pair hangs on the rack to cool. In the shed in November that takes a minute or two; on a warm September afternoon it can take four or five.

The test for when to dip again is a knuckle against the wax. The candle should feel cool and firm, no longer soft, but not cold. Wax laid over cold wax does not bond well, and a taper built that way can crack along its layers weeks later. Wax laid over warm wax slides and sags. Somewhere between thirty and forty-five dips a pair reaches the width I want, which on a good afternoon means six or eight pairs in rotation on the rack.

When a pair is nearly done, I dip the tips a few extra times to build the shoulder, then trim the drip that forms at the bottom with a warm knife while the wax is still leather-soft. A last dip a few degrees hotter, at around seventy-eight, gives a smooth and glossy skin. The finished pair hangs for at least two days before the wick is cut, and the tag goes on with the date, the wax card number and the wick size.

Written up in the shed at the Rėkyva garden plots, Šiauliai, from the pencilled book above the pot. Temperatures are read from a glass jam thermometer and wick sizes come from my own test burns; your wax, room and candlesticks will differ, so burn a test pair before trusting any number here.Back to all shed notes